![]() ![]() Fawn Creek Township is in Montgomery County. Meanwhile, the reasons of different influence of these fillers were analyzed during microstructure changes of PEEK composites with SEM photographs. Fawn Creek Township is located in Kansas with a population of 1,618. The influence of expanded graphite and nano particles TiO2 on mechanical properties of PEEK composites was also be studied here. However, the tensile modulus kept constant during the change of PTFE content. With the increasing of PTFE content, the tensile strength was increased at first and then decreased rapidly. If the weight percent of short fibers was more than 10%, this increasing tendency became slowly. Key Properties Superior High Temperature Performance Retention of Mechanical and Physical Properties to Temperatures 54F (30C) Higher Than Standard PEEK Up. 9 min read Polyether ether ketone (PEEK) plastic is a highly coveted engineering material, thanks to its superb blend of strength, resistances, and workability. The results showed, with increasing of the weight content of short fibers, the tensile performance (tensile strength and modulus) of PEEK composites was increased rapidly. The weight content of short fibers, PTFE and expanded graphite was varied from 0-15%, and of TiO2 was varied from 0-8%. ![]() Plastic Products is your complete source for any plastics material.Į-mail, call or fax your requirements today.The tensile properties of polyetheretherketone (PEEK) composites, which were reinforced with short fibers, such as short carbon fiber (SCF), short glass fiber (SGF), or filled with polytetrafluoroethylene (PTEF), expanded graphite and nano material TiO2 were examined and studied. It is a linear, aromatic, semi-crystalline polymer widely regarded as one of the highest performing thermoplastics in the world. All trade and patent rights should be observed. VICTREX PEEK polymer provides exceptional performance over a wide range of temperatures and extreme conditions. This information is only to assist and advise you on current technical knowledge and is given without obligation or liability. It provides a unique combination and range of high performance properties. Profiles, tubes and special sizes are custom-produced on request PEEK Materials Properties Guide VICTREX PEEK polymer provides exceptional performance over a wide range of temperatures and extreme conditions. Plates: 1/4″ to 2″ thickness inclusive are 24 X 48 inchesĢ 1/4″ to 4″ thickness inclusive are 12 X 48 inches Rods: Length: 10 feet – Diameters 1/4″ to 6″ Physical PropertiesĬoefficient of friction 68☏, 1200 in/min, 155 lbs. PEEK has superior chemical resistance, and. PEEK Cost The biggest difference between these two plastics is cost. Characteristics PEEK has superior resistance to hot water, and can be used continuously in steam at 200 to 260C. The addition of glass fiber and carbon fiber reinforcements enhances the mechanical and thermal properties of the basic PEEK material. High strength and stiffness Broad chemical resistance Low smoke generation Excellent fatigue and stress crack resistance Ultem vs. Especially significant in this regard is PEEK’s ability to retain it flexural and tensile properties at very high temperatures - in excess of 250☌ (482☏). Polyetheretherketone (PEEK) is a high-performance thermoplastic material that is an excellent choice for demanding applications. PEEK(polyetheretherketone) PEEK, a unique semi-crystalline, high-temperature engineering thermoplastic, is an excellent material for a wide spectrum of applications where thermal, chemical and combustion properties are critical to performance. Please allow us the opportunity to quote your requests. In short, we can be your complete source for nearly anything plastic and can further assist you with our manufacturing expertise. 1-3 PEEK is a thermoplastic with exceptionally high melting and glass transition temperatures due to its crystallinity and its stiff backbone interconnected by ketone and ether groups. ![]() Plastic Products offers an extensive line of plastic materials and has complete facilities for plastic molding, machining & fabrication. The first effort to synthesize PEEK occurred in 1967 and Victrex PEEK was commercialized by Imperial Chemical Industries in 1982. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |